This Agfa Isolette III was made by the German firm of Agfa in the early 1950s. Agfa is an old company and has a chequered history. Agfa was formed in 1867 to produce the new aniline dyes. Agfa is an acronym for Akliengesellschaft für Aniline which translates into English as Corporation for Aniline Production. The dye company branched out into making photographic film in 1898 and later into making cameras.
After the First World War, the German economy was in dire straits and many companies merged to survive. The most famous of these, photographically, was the mergers that formed Zeiss Ikon in 1926. The same conditions applied to the chemical industries and in December 1925, Agfa, Bayer, BASF, Hoechst and a couple of others merged to form the infamous IG Farben. Within the IG Farben conglomerate, Agfa was merged with Bayer.
After WWII, IG Farben was demerged back to its constituent businesses (IG Farben still exists as a company but does not produce anything. It is now a part of the University of Frankfurt). Agfa was a wholly owned subsidiary of Bayer at this point. In 1964, Agfa merged with Gevaert to form Agfa-Gevaert, with Bayer owning 50% of the new company – in 1981, Bayer bought out Gevaert and became the sole owner of Agfa-Gevaert, which continued until 1999 when Agfa -Gevaert became a public company.
So, this Agfa camera. It was made in the early to mid 1950s. I cannot date it precisely but this model was revised a couple of times and my camera is the original version. The Isolette range is a beginner’s range, really, and the specification is close to basic. that is not to say that the camera is not well made – it is – nor that it is not capable of producing good photographs – again, it is. The model III – this one – is distinguished by having a built-in rangefinder. This is an un-coupled rangefinder – the measured distance must be transferred to the focus ring by hand but it is still very useable.
The body seems to be made from aluminium, apart from the lens door which is steel. The metal is painted with matt black paint with most of the outside being covered with a very plasticky black leatherette with a pronounced ribbed pattern. The top plate is pressed brass which is satin plated – the metal has a blueish tint so I think the plating might be nickel but I cannot be sure it is not chrome.
focal length: 85 mm
apertures: ƒ/4.5 to ƒ/32
focus range: 3.5 feet (1 metre)
lens fitting: fixed
shutter: Prontor SV
speeds: 1 to 1/300 s
flash: PC socket
film size: 120
Starting with the top plate: on the right is the film advance. This is a fairly flat milled wheel with a curved arrow on top to indicate the correct direction to turn the advance wheel (anti-clockwise) although it is not actually possible to turn the wheel the other way. This advance wheel pulls up to release the take-up spool inside – see later. At the front of the top plate by the advance wheel is a small hole in the top plate. When the shutter release button is pressed, this hole shows a red flag which turns white when the advance wheel is turned.
Close to the film advance wheel is the shutter release button. This connects to the actual shutter by a hinged linkage which articulates when the lens door is either opened or closed. This button is plated metal and is threaded for a standard Gauthier cable release. This button is connected to the film advance wheel. Once the button has been pressed, it cannot be pressed again until the film advance wheel has been turned. This is to prevent accidental double exposures.
To the left of the shutter release button the top plate is raised. This is to accommodate both the viewfinder and the rangefinder. At the back of the raised portion of the top plate, on the right, is a vertical, toothed, wheel – this is the rangefinder adjuster. The way that this works is when looking through the viewfinder there is a central bright spot. The viewfinder image is distinctly pink and this central spot is slightly yellow/green – this gives good contrast between the viewfinder and rangefinder images. You move the camera until this bright spot is over your subject. In the bright spot, you should see a double image of your subject. You turn the toothed rangefinder wheel until the two parts of the double image are exactly superimposed. In front of the toothed wheel is a distance scale. When the double image is reduced to a single image, you read the distance off this scale and set the lens focus scale to the same distance.
In the centre of the top plate is a standard Barnack accessory shoe. there are no electrical contacts here so this is a “cold” shoe.
On the back of the top plate, just left of the accessory shoe, is the viewfinder eyepiece. This is small and circular with a diameter of 5 mm. This was a common size of viewfinder eyepiece in the mid 1950s. This camera is not an SLR so there is no focus screen – you are looking straight through the viewfinder which acts as a small telescope. Technically, this is a reverse Galilean telescope – the ‘reverse’ bit means the image is smaller than life-size like looking through a telescope backwards.
On the left of the raised portion of the top plate is a button that looks very much like the shutter release button. Pressing this button releases the lens door on the front of the camera – the lens door snaps downwards nicely and locks itself in position.
On the far left of the tyop plate is a second milled wheel – this top plate is nearly symmetrical. This second milled wheel is a depth of field calculator. In the centre of the wheel is a static focus scale from three feet to infinity (For our non-British or American readers, three feet is essentially one meter). Around this is a turnable aperture scale. To use this, you set your chosen lens aperture against the appropriate distance of the focus scale. Either side of each aperture is a delimiting line – these lines indicate the nearest and furthest distances that will be in focus for those settings. This does not alter the working of the camera, it is just for information.
On the front of the top plate are two square windows. These are both 8 mm square. The one on the right, while looking at the front of the camera, is the viewfinder window and the one on the left is the rangefinder window.
Below the top plate, on the front of the camera, is the lens door. This measures 72 mm wide by 65 mm high. On the front of this is embossed the Agfa logo, the legend “AGFA ISOLETTE III” and the legend “MADE IN GERMANY” indicating that this is an export item. As already mentioned, this door is opened by pressing the left-hand button on the top plate. This door is spring loaded and snaps to with no help from the user, pulling the shutter/lens assembly to its working position. This lens door is held in position by two chrome straps. To close this lens door, you press down on the hinge in the middle of each strap and fold up the door. The shutter/lens assembly is connected to the camera body by black leatherette bellows.
The shutter is a Prontor SV by Gauthier. There is a variety of different Prontor SV shutters – this one has the legend Ah4 on it which I assume denotes the type of Prontor SV shutter. The Prontor SV offers eight shutter speeds plus B. This is the ‘old’ range of speeds which are not entirely rational. In a rational system, moving from one speed to the next will either double or half the speed. Not so here. The first two speeds are rational – 1 second and 1/2 second – then we go from 1/2 to 1/5 seconds, then halving from 1/5 to 1/10 seconds, irrational again from 1/10 to 1/25. halving again from 1/25 to 1/50 to 1/100 and finally irrationally from 1/100 to 1/300 second. The shutter speed is set by turning a milled ring around the front of the shutter housing.
At the back of the shutter housing is the aperture scale. This is adjusted by a sliding pointer. The scale runs from ƒ/4.5 to ƒ/32. ƒ/4.5 is not very fast but was quite good for an ordinary camera in 1952. ƒ/32 would be quite useful in the summer given the slowish top shutter speed of 1/300 second. On the right hand end of the aperture scale is a second cable release socket – again with the Gauthier standard conical thread. This socket will allow you to fire the shutter even if the film has not been wound on.
On the left hand end of the aperture scale is a PC flash socket. This is in the original form of a pillar rather than the more modern recessed socket. Next to this is a synchronising selector. This has two positions – X and M. X is for electronic flash and fires the flash as soon as the shutter is fully open. M is for Magnesium flash bulbs and fires the flash a few milliseconds early to allow the flash bulb to burn to maximum brightness before the shutter opens. These are colour coded – X is red and M is yellow. These are used in conjunction with the delay action lever at the base of the shutter housing. For X sync, the sync selector must be on X and the delay timer lever can either be left alone for immediate action or moved across to give a delay before the flash and shutter fire. For M sync, the sync selector must be on M and the delay timer lever moved to the yellow dot. There will be no delay before the shutter is fired, the delay mechanism is only providing the timing for the flash synchronising.
The delay timer lever can, of course, be used without flash – the flash sync selector must be set to X – when, on my camera, you get a delay of eleven seconds between pressing the shutter release and the shutter firing. I ought to mention the standard advice to never use the delay lever on an old camera as the delay mechanism is the weakest part of the shutter mechanism and if it fails the shutter will be wrecked.
The lens is an Agfa Apotar lens. This is a triplet (made from three pieces of glass) and should perform quite well if the aperture is closed down to ƒ/8. The lens focal length is 85mm and the surfaces are coated. The focus scale runs from three feet to infinity – this is an export camera so the scale is in feet rather than metres, three feet is as good as one metre. On the focus scale, two distances are in red – ten feet (three metres) and 30 feet (ten metres). These are Happy Snapper settings and are used in conjunction with a red dot on the aperture scale. This red dot is at about ƒ/10 – actually just short of ƒ/11. To use the Happy Snapper settings, set the aperture to the red dot and the focus scale to either ten feet or thirty feet. The ten foot Happy Snapper setting is intended for group portraits. With this setting, everything between eight and thirty feet will be in focus. The thirty foot Happy Snapper setting is for landscapes and everything between fifteen feet and infinity will be in focus. – this is the hyperfocal distance for this lens at ƒ/10.
The back of the camera is plain. In the centre is a chrome slide. Sliding this down reveals a red window through which the user can read the frame numbers on the film’s backing paper. There is no automatic control for frame spacing so the user winds on the film until the next frame number is centred in the red window. The metal slide is there to prevent any light entering through the red window and fogging the film between shots.
The back is opened by a sliding catch on the left hand edge of the camera body. In the centre of the inside of the back is a sizeable sprung pressure plate. This keeps the film flat against the film gate. In the middle of the pressure plate is an oblong hole which lines up with the red window. Around the edges of the back are sizeable flanges which fit into a groove around the edges of the body. This provides light tightness – as this is a German camera, there are no foam light seals to go bad.
The inside of the body is as you might expect from a medium format folding camera. In the centre is the film gate – this is 56 mm square (the nominal size is 60 mm square but some of the film must be sacrificed to sit against the metal of the film gate). The surround of the film gate is pressed brass, painted black.
Either side of the film gate are the chambers for the film spools. The new spool of film goes on the left. To aid fitting the film, there is a hinged cradle which moves out of the chamber to take the spool of film – this is nickel plated. As well as the cradle hinging out of the chamber, the top of the cradle is also hinged. Halfway along the cradle is a spring to stop the film from loosening on the spool.
The take-up spool goes on the right – the take-up spool is the empty spool from the previous roll of film. To either insert or remove this take-up spool, it is necessary to pull up the film advance wheel on the top plate. There is no hinged cradle on this side – the empty spool locates onto a stud at the bottom and when the film advance wheel is pushed in again there is a key which fits into a slot on the end of the spool.
On either side of the film gate, beside each of the spool chambers, is a chrome roller to allow the film to change direction as it is advanced without becoming scratched.
5 thoughts on “Agfa Isolette III”
I have the exact same model but with zone focusing and no rangefinder. However, it has the ANSCO name on it. the American firm of Ansco was once a strong rival to Kodak and actually invented photographic roll film. In fact, it is my understanding that the “A” in Ansco also stands for “Aniline.” As a historical note, Ansco received an extremely large settlement from Kodak because Kodak stole the idea for roll film from Ansco. From what I have heard, George Eastman was not that nice of a guy. I remember back in the 70s using Ansco 400 ASA (ISO) speed slide film. Took some great photos with it. Since Ansco was marketing Agfa cameras under their name, I wonder if the firm was also marketing Agfa film under the Ansco name. I have heard great things about Agfa film but never used it, at least under that brand name.
Agfa bought Ansco and merged their North American operations so in north America Agfa cameras were sold as Agfa Ansco. That stopped when Germany declared war on the USA and Agfa Ansco became GAF. All three – Agfa, Ansco and GAF – have aniline in their name.
Now, roll film! First roll film was in 1875 and made by Warnerke in Germany – this built on a 1854 patent belonging to Spencer and Melhuish. George Eastman was a late-comer to the game with his first roll film in 1885. First photographic film (as opposed to glass plates) was made in 1856, patented by a chap called Parkes. This was sheet film, I think, rather than roll film.
My apologies to Leon Warnerke, he was Russian, not German.
Thanks John. I didn’t know that Agfa owned Ansco. So, I guess I did use a lot of Agfa film!
Thanks so much for the Isolette III info. I’ve looked at what appears to be a shortened manual but could not figure out what the red and yellow dots were till this description. I’m having problems with shutter release despite Certo6 cleaning and adjustment awhile ago. Still working on this aggravation.