Canon FX

Canon FX film SLR camera from Japan.

For the last 18 months, I have been concentrating my collecting on Nikon and Canon SLR cameras. My latest acquisition is this Canon FX. It is not a professional camera but it is well designed and well made. It dates from 1964.

  • lens: n/a
  • focal length: n/a
  • apertures: n/a
  • focus range: n/a
  • lens fitting: Canon FL mount
  • shutter: Cloth focal plane
  • speeds: 1 second to 1/1000 second
  • flash: 1 x PC connector
  • film size: 35mm

The body is made from cast aluminium alloy with pressed brass top and base plates – these are satin chrome plated on my camera but a few were made with black enamelled top and base plates. The body is covered with black textured leatherette. This camera has been stored in very damp conditions – I suspect a garage – and the aluminium body has significant corrosion and there is quite a bit of mildew on the shutter curtains. Some collectors would reject this camera based solely on condition, but I like my cameras to be in used condition and this is all a part of the camera’s story.

The size of the camera is pretty normal for a 35mm SLR. It measures 142 by 91 by 86 mm and the body with no lens attached weighs 670g. While 670g is not light – it is heavier than any of my Japanese rangefinders – it is not as heavy as many SLR cameras: Nikon F2, 840g; Nikkormat FT, 754g; Canon FTb, 750g; Ricoh 500, 800g.

So, now for a description of the camera starting with the top plate. The right hand side of the top plate is pretty much standard. Far right is the film advance lever. This is cut metal and plated (or anodised) to match the top plate. This has two rest positions – flush with the edge of the top plate or sticking out about 10 mm. The lever moves through 160º to advance one frame. The lever is on a ratchet so the film can be advanced with several short motions if required.

In front of the film advance lever is the window for the frame counter. This is reset by opening the camera back – it resets to S which is -2. Zero is in orange. Even numbered frames have numbers and odd numbered frames are just dots. Frames 20 and 36 are also in orange as these were the standard film lengths in 1964.

To the left of this frame counter window and still at the front of the top plate is the shutter release button. This is chrome plated metal and is threaded for a standard Gauthier cable release. Around the shutter release button is a rotating collar. This will rotate to one of two positions marked ‘A’ and ‘L’. ‘A’ is the working position and in this position the shutter can be fired. ‘L’ is the lock position and in this position the shutter release button cannot be depressed to fire the shutter but the shutter can still be fired by using a cable release. As well as functioning as a safety device to prevent accidental exposures, the ‘L’ position can be used with the B shutter speed setting to lock the shutter open for long exposures.

Left again is the combined shutter speed and film speed selector dial. Film speeds are selected by slightly lifting the selector dial and turning. There are two windows in the top of the dial to show the selected film speed – one for DIN and one for ASA. The film speeds available to be set range from 11 DIN/10 ASA to 30 DIN/800 ASA. The film speed numbers are in one stop increments but there are 1/3 stop increments available denoted by dots between the numbers. The numbers were originally painted in orange but the conditions that the camera has been stored in means that nearly all the orange paint has corroded away, making the setting hard to impossible to read.

Shutter speeds are selected by just turning the selector dial. Shutter speeds range from one second to 1/1000 second plus B and X. The index mark for the shutter speeds is to the left of the dial. The dial moves freely between speeds but not directly between B and X. B is ‘bulb’ and with this setting the shutter will remain open while the shutter release button is depressed. X is the electronic flash sync setting. The manual tells me that this is 1/60 seconds and I am not entirely sure why the user cannot just set the shutter speed to 1/60 as on all the other cameras I have seen but the manual is clear that the X setting should be used. It might be because the 1/60 sync speed is nominal and is actually slightly slower. 1/30 and slower can be used with electronic flash as well as X.

Towards the rear of the top plate, behind the shutter speed dial, is an engraved circle with a line through it. The line represents the position of the film plane inside the camera. This is intended for when the user is relying on measuring the focus distance rather than focusing by eye on the focus screen.

In the middle of the top plate is the pentaprism hump. Inside the hump is the focus screen. This is mostly a Fresnel screen with a central circle of ground glass for focusing. In the middle of this central circle is a split-image rangefinder. As there is no TTL meter, there is no information provided on the screen. My camera has been stored for a long time in damp conditions and this has had a deleterious effect on the silvering on the pentaprism. This silvering has peeled away from the edges. This makes the image on the focus screen less clear but will make no difference to the photographic image.

On the top of the pentaprism hump is the accessory shoe. This is a standard Barnack shoe – no electrical contacts so this is a cold shoe. The front of the pentaprism hump has the Canon logo engraved on it.

Left of the pentaprism hump, towards the front of the top plate, is the camera serial number. Behind this, by the back of the top plate, is the light meter readout. This works in a way that I have never seen before. First, you set your required shutter speed. As you rotate the shutter speed dial, the aperture scale in the readout moves – in fact, there are two aperture scales, both of which move. One scale is orange (for use in low light) and one scale is white (for use in bright light). Second, you set the meter sensitivity by a lever around the rewind crank. This lever has two settings: ‘L’ for low sensitivity (or bright light) and ‘H’ for high sensitivity (or low light). The meter needle should now point to the aperture value which you set on the lens aperture ring. this is an entirely manual camera even though it has a light meter and you can ignore the light meter altogether if you wish to.

On the left hand end of the top plate is the rewind crank. This is the usual small folding crank. Unusually, the crank has no other function – it does not unlock the camera back. Around the rewind crank is the meter sensitivity switch already mentioned.

On the rear of the top plate, behind the meter readout, is a dial to switch the light meter on or to check the battery condition. On the front of the top plate, in front of the rewind crank, ids a circular meter sensor. The remaining component of the meter is the battery chamber. This is on the left hand end of the camera. It is intended to take a type 625 mercury 1.3 volt battery which is no longer available. However, you can get 1.5 volt alkaline 625 batteries which will work but not accurately. On my camera, the meter does not work at all.

So, moving to the front of the camera. In line with the pentaprism hump is a raised portion containing the lens mount. This is a three pronged bayonet mount. Canon’s SLR cameras (before the modern EF mount) used three different bayonet mounts. The first was the R mount. Canon upgraded this to the FL mount – R mount lenses would fit. Later, the FL mount was upgraded to the FD mount – again, both R mount and FL mount lenses would fit. The reverse is also true – FD lenses will fit R mount and FL mount cameras and FL lenses will fit R mount cameras. These three, R, Fl and FD mounts were all breech lock mounts where there is a locking ring to fix the lens in place rather than having to turn the whole lens to lock them.

This camera uses the FL mount and this FX model was the first model to use the FL mount. The FL mount offers little apart from attaching the lens. There is a lever to close the aperture on the lens just prior to the shutter firing and that is it.

To the right of the lens mount, towards the top of the body, is a small rotating lever. Turning this anticlockwise 1/4 turn will raise the mirror. This is for use in critical photography as it removes the vibration caused when the mirror flips out of the way.

Below this is a PC connector for attaching a flash gun. On the left of the lens mount is another rotating lever. This one is the self-timer mechanism. Turning this a half turn anticlockwise gives a delay of ten seconds between pressing the shutter release button and the shutter firing. I timed this with my phone’s stop watch and it was just about exactly ten seconds as close as I could time it – not bad for a 57 year old mechanism. Turning this lever just over a quarter turn will give a delay of six seconds – this is as short as I could make it work.

Moving to the base of the camera, this is fairly sparse. There are no facilities for connecting a power winder and no battery compartment. Towards the front of the base plate, in line with the centre of the lens, is a tripod socket. This is a 1/4 inch Whitworth thread. Also on the base plate is the rewind button. This does not need to be held in once you start rewinding the film which makes life easier. There is a small dot on the rewind button. As you rewind the film, the rewind button rotates and this dot makes it easier to see the rotations. Once the rewind button stops rotating, you know that the film leader is clear of the take-up spool and you can stop rewinding. Stopping at this point means that the film leader is still protruding from the cassette. Not only does this make it easier to extract the film for developing, it also means that the film is blocking the felt light trap on the lips of the cassette, reducing the risk of light entering and fogging the film.

At the other end of the base plate is a folding recessed key. Lifting this and rotating it 1/4 turn anti-clockwise releases the camera back. Opening the back, there is a relatively small pressure plate. To the left of this is a chrome bar across the height of the back. This keeps the film snug against the sprocket shaft. On the right-hand end of the back is a slightly sprung plate which keeps the film cassette snug in its chamber.

The edges of the back form a flange that fits into a groove on the camera body. this flange is not big enough to fully render the joint between the back and body light tight so the groove on the body contains a foam light seal that the flange presses against. This camera is 57 years old and the foam light seal has degraded to a granular mess. I shall have to replace it before I can use this camera which is a simple enough job.

The inside of the body has the chamber for the film cassette on the left. Protruding into this is the fork for the rewind crank.This can be raised out of the way by raising the rewind crank. The film gate is central and gives on to the shutter curtains. This shutter has two horizontally travelling cloth curtains. With these focal plane shutters, the shutter always travels at the same speed – shutter speed is changed by altering the width of the gap between the two curtains. The narrower the gap, the fast the effective shutter speed. As mentioned earlier, my camera has been stored in very damp conditions and there is significant mildew on the shutter cloth.

To the right of the film gate is the sprocket shaft. This has teeth that engage in the holes on the edges of the film. When advancing the film, this sprocket shaft will stop once eight holes have moved passed the shaft – eight holes equals one frame. To the right of the sprocket shaft is the take-up spool. This has a single slot for attaching the film leader. The take-up spool turns clockwise. This means that is stores the film emulsion side outermost – doing this reduces the amount of curl in the film once it has been developed and aids the film lying flat when being printed from (or when being scanned in our digital world).

Author: John Margetts

I am a keen photographer who also collects cameras. I am retired with about 50 years photography experience.

2 thoughts on “Canon FX”

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: